Figure 29.4: Demonstration of the use of interpn
뒤로: One-dimensional Interpolation, 위로: Interpolation [차례][찾아보기]
There are three multi-dimensional interpolation functions in Octave, with similar capabilities. Methods using Delaunay tessellation are described in Interpolation on Scattered Data.
Two-dimensional interpolation.
Interpolate reference data x, y, z to determine zi
at the coordinates xi, yi. The reference data x, y
can be matrices, as returned by meshgrid, in which case the sizes of
x, y, and z must be equal. If x, y are
vectors describing a grid then length (x) == columns (z)
and length (y) == rows (z). In either case the input
data must be strictly monotonic.
If called without x, y, and just a single reference data matrix
z, the 2-D region
x = 1:columns (z), y = 1:rows (z) is assumed.
This saves memory if the grid is regular and the distance between points is
not important.
If called with a single reference data matrix z and a refinement
value n, then perform interpolation over a grid where each original
interval has been recursively subdivided n times. This results in
2^n-1 additional points for every interval in the original
grid. If n is omitted a value of 1 is used. As an example, the
interval [0,1] with n==2 results in a refined interval with
points at [0, 1/4, 1/2, 3/4, 1].
The interpolation method is one of:
"nearest"Return the nearest neighbor.
"linear" (default)Linear interpolation from nearest neighbors.
"pchip"Piecewise cubic Hermite interpolating polynomial—shape-preserving interpolation with smooth first derivative.
"cubic"Cubic interpolation (same as "pchip").
"spline"Cubic spline interpolation—smooth first and second derivatives throughout the curve.
extrap is a scalar number. It replaces values beyond the endpoints
with extrap. Note that if extrap is used, method must
be specified as well. If extrap is omitted and the method is
"spline", then the extrapolated values of the "spline" are
used. Otherwise the default extrap value for any other method
is "NA".
Three-dimensional interpolation.
Interpolate reference data x, y, z, v to determine
vi at the coordinates xi, yi, zi. The reference
data x, y, z can be matrices, as returned by
meshgrid, in which case the sizes of x, y, z, and
v must be equal. If x, y, z are vectors describing
a cubic grid then length (x) == columns (v),
length (y) == rows (v), and
length (z) == size (v, 3). In either case the input
data must be strictly monotonic.
If called without x, y, z, and just a single reference
data matrix v, the 3-D region
x = 1:columns (v), y = 1:rows (v),
z = 1:size (v, 3) is assumed.
This saves memory if the grid is regular and the distance between points is
not important.
If called with a single reference data matrix v and a refinement
value n, then perform interpolation over a 3-D grid where each
original interval has been recursively subdivided n times. This
results in 2^n-1 additional points for every interval in the
original grid. If n is omitted a value of 1 is used. As an
example, the interval [0,1] with n==2 results in a refined
interval with points at [0, 1/4, 1/2, 3/4, 1].
The interpolation method is one of:
"nearest"Return the nearest neighbor.
"linear" (default)Linear interpolation from nearest neighbors.
"cubic"Piecewise cubic Hermite interpolating polynomial—shape-preserving interpolation with smooth first derivative (not implemented yet).
"spline"Cubic spline interpolation—smooth first and second derivatives throughout the curve.
extrapval is a scalar number. It replaces values beyond the endpoints
with extrapval. Note that if extrapval is used, method
must be specified as well. If extrapval is omitted and the
method is "spline", then the extrapolated values of the
"spline" are used. Otherwise the default extrapval value for
any other method is "NA".
Perform n-dimensional interpolation, where n is at least two.
Each element of the n-dimensional array v represents a value
at a location given by the parameters x1, x2, …, xn.
The parameters x1, x2, …, xn are either
n-dimensional arrays of the same size as the array v in
the "ndgrid" format or vectors. The parameters y1, etc.
respect a similar format to x1, etc., and they represent the points
at which the array vi is interpolated.
If x1, …, xn are omitted, they are assumed to be
x1 = 1 : size (v, 1), etc. If m is specified, then
the interpolation adds a point half way between each of the interpolation
points. This process is performed m times. If only v is
specified, then m is assumed to be 1.
The interpolation method is one of:
"nearest"Return the nearest neighbor.
"linear" (default)Linear interpolation from nearest neighbors.
"pchip"Piecewise cubic Hermite interpolating polynomial—shape-preserving interpolation with smooth first derivative (not implemented yet).
"cubic"Cubic interpolation (same as "pchip" [not implemented yet]).
"spline"Cubic spline interpolation—smooth first and second derivatives throughout the curve.
The default method is "linear".
extrapval is a scalar number. It replaces values beyond the endpoints
with extrapval. Note that if extrapval is used, method
must be specified as well. If extrapval is omitted and the
method is "spline", then the extrapolated values of the
"spline" are used. Otherwise the default extrapval value for
any other method is "NA".
A significant difference between interpn and the other two
multi-dimensional interpolation functions is the fashion in which the
dimensions are treated. For interp2 and interp3, the y-axis is
considered to be the columns of the matrix, whereas the x-axis corresponds to
the rows of the array. As Octave indexes arrays in column major order, the
first dimension of any array is the columns, and so interpn effectively
reverses the ’x’ and ’y’ dimensions. Consider the example,
x = y = z = -1:1; f = @(x,y,z) x.^2 - y - z.^2; [xx, yy, zz] = meshgrid (x, y, z); v = f (xx,yy,zz); xi = yi = zi = -1:0.1:1; [xxi, yyi, zzi] = meshgrid (xi, yi, zi); vi = interp3 (x, y, z, v, xxi, yyi, zzi, "spline"); [xxi, yyi, zzi] = ndgrid (xi, yi, zi); vi2 = interpn (x, y, z, v, xxi, yyi, zzi, "spline"); mesh (zi, yi, squeeze (vi2(1,:,:)));
where vi and vi2 are identical. The reversal of the
dimensions is treated in the meshgrid and ndgrid functions
respectively.
The result of this code can be seen in Figure 29.4.
뒤로: One-dimensional Interpolation, 위로: Interpolation [차례][찾아보기]